Which lubricating oil is in series PP 40x / PP 80 x used for shafts?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

PSi uses a lubricating oil “ISOFLEX PDP 61A”

The manufacturer is:
Fa. Klüber Lubrication
Geisenhausener Straße 7
81379 München
Tel.:0049 89 78760
www.klueber.de

Alternatively, you can also use a good typewriters oil.

Schmiermittel Datenblatt

What is the difference of a relative to the absolute horizontal position

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]
  • The Absolute Pos goes. From always from the left edge.
  • A Relative Position refers. To the last character.
  • Example of print position 1/2 “(30/60”) from the left edge
    HEX : 1B 24 1E 00
    DEC : 27 36 30 00
  • Horizontal Pos. Relative = from the last printing position
    HEX :1B 5C P1 P2
    Draft – Mode (P1 + P2 * 256) * 1/120
    LQ – Mode (P1 + P2 * 256) * 1/180
  • Example of print position in Data – Mode 1/2 “(60/120”) from the last position
    HEX : 1B 5C 3C 00
    DEC : 27 92 60 00
  • Example of print position LQ mode 1/2 “(90/180” is) from the last position
    HEX : 1B 5C 6A 00
    DEC : 27 92 90 00

How to install a Printer Stand PP 803 ?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

FSI_19273

How to install a Printer Stand PP 806 / PP 809 ?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

FSI_19273

My matrix printer prints very slowly from a Windows environment

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

It is recommended to use the PSi original printer driver and use of the application only internal printer fonts. TrueType fonts are fonts graphics printed with graphics speeds.
However, if the need TrueType fonts to use, the PP40x) and all models offer the possibility of accelerating the Grafidruckes. In macro menu setting the print quality is there, the menu item for graphic quality.
The following settings are possible:

  • Standard
  • WIN LQ 180 dpi
  • WIN NLQ 90 dpi
  • WIN DRAFT 60 dpi

Depending on the print quality, the printing speed is to be increased. However, the font size is retained. Likewise, these settings can be made in the printer driver.

Grafikbeschleunigung

How can internal barcodes on a PP 40x / 80x PP print from Windows?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

Use an internal font in your application. Enter Barcode commands and start / stop commands. These are described in the User Guide Barcode Quick Reference Guide. Use $$ instead of ESC [and select the Printers menu $$ – Emulation. The bar code is not shown on the screen.

How can the performance be increased in barcode printing?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

Printed with the Font Data also bar with PSi sequences, optimizing performance is possible.
The parameter P7 should preferably be set to the value “3” in the barcode sequence on the system side. Then the PSi barcode is printed in “NLQ unidirectional”. This is sufficient for most applications. Tests with readers, however, are recommended.

ESC[;P2;P3;P4;P5;P6;P7_z (Note:_ = Space)

Background:
By default, the printer uses the parameter P7 is “1” (= LQ unidirectional). For this, the print head must also be brought into the appropriate position. If the surrounding text in DATA / DRAFT printed in the other print head position, here switchover pauses are inevitable.

Details see Appendix Barcode Quick Reference Manual of the respective printer

Buffer Overflow by operating serial interfaces

Verlust von Einstellungen im Menü. Der Drucker hat plötzlich wieder Fabrikeinstellungen.

[bsf-info-box icon="Defaults-close remove times" icon_size="32" icon_color="#dd3333"][/bsf-info-box]

Cause of

The pull-up resistor for the Cond CTS (PIN 5 on 25-pol. Connector) is not due to + 12V to + 5V but. Thus, sending X-OFF / X-ON is non-connected at
CTS -Ltg. suspended because the level does not min. 3V reached.

[bsf-info-box icon="Defaults-check" icon_size="32" icon_color="#81d742"][/bsf-info-box]

Solution

Set a Bridge from PIN 20 to PIN 5 in the cable or connector PM.

Which grease can used to lubricate the moving parts of the cutter?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

PSi used to lubricate the moving partsthe grease POLYLUB GLY 151

the manufacturer is

Fa. Klüber Lubrication
Geisenhausener Straße 7
81379 München
Tel .: 004989 78760
www.klueber.de

Schmierfett

How to adjust the tear off position in PP80x printers?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

The tear bar may in the installation menu in increments of 1 – are laid 360/60 up to 6 inches. Refer to the instruction.

Verlegen der Tear off Position in PP80x

How to read the ribbon code PP 80x

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

1156-Farbbandcode_deu

 

 

 

 

 

 

  • Digit 1 is always an 8 (means PSi)
  • Digit 2 is the last digit of the year (in the example 2012)
  • Digit 3 + 4 is the calendar week of the year

How to perform a HEX-Dump in PP 80x printers?

The HEXdump provides the ability to stream to analyze. It shows all control characters, which are sent to the printer. To this end, the HEX-DUMP is selected in the menu. Then you send the original file to the printer. All data are printed in HEX code line by line.

Hex_dump_80x

Perform a HEX-DUMP PP80x

How to increase the speed in draft mode (HSD)

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

The quality of the font data can be selected in 2 steps or 2 speeds.

Does not print accents from Windows with new drivers on older PP 40x printers

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

In all new Windows printer drivers of PSi a code page ISO 8859-15 is used with the Euro symbol. In older printers, this code page is not available, so the printer in this command will fall back to its default character set. In older printers is only character set ISO 8859-1 available . This should selected and saved in all macros. This ISO set has all characters without the euro symbol (this will then printed as a graphic sign).

Which lubricating oil is in series PP 40x / PP 80 x used for shafts?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

PSi uses a lubricating oil “ISOFLEX PDP 61A”

The manufacturer is:
Fa. Klüber Lubrication
Geisenhausener Straße 7
81379 München
Tel.:0049 89 78760
www.klueber.de

Alternatively, you can also use a good typewriters oil.

Schmiermittel Datenblatt

What is the difference of a relative to the absolute horizontal position

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]
  • The Absolute Pos goes. From always from the left edge.
  • A Relative Position refers. To the last character.
  • Example of print position 1/2 “(30/60”) from the left edge
    HEX : 1B 24 1E 00
    DEC : 27 36 30 00
  • Horizontal Pos. Relative = from the last printing position
    HEX :1B 5C P1 P2
    Draft – Mode (P1 + P2 * 256) * 1/120
    LQ – Mode (P1 + P2 * 256) * 1/180
  • Example of print position in Data – Mode 1/2 “(60/120”) from the last position
    HEX : 1B 5C 3C 00
    DEC : 27 92 60 00
  • Example of print position LQ mode 1/2 “(90/180” is) from the last position
    HEX : 1B 5C 6A 00
    DEC : 27 92 90 00

How to install a Printer Stand PP 405 ?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

FSI_19273

How to install a Printer Stand PP 407 ?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

FSI_19273

How to install a Printer Stand PP 408 ?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

FSI_19273

What factors are important when LPR Printing with PM PNS PP 40x

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

For LPR Printing from Windows the byte count must be activated .

1064-lpr_001

 

 

 

 

 

 

 

 

 

 

 

Reason:

“LPR Byte Counting” forcing Windows to count the number of bytes in the file and sends this value to the data of the received file as a command. If LPR byte count is disabled, Microsoft puts on a size which is much larger than the actual file size. It is neither 0 nor the actual file size.

What are the causes of errors in horizontal series PP40x printers?

[bsf-info-box icon="Defaults-close remove times" icon_size="32" icon_color="#dd3333"][/bsf-info-box]

Possible Cause 1:

The print head cable is defective. (Line break)

[bsf-info-box icon="Defaults-check" icon_size="32" icon_color="#81d742"][/bsf-info-box]

Solution
Order numberns

  • PP 404 old – 5322 320 12219 Print Head Cable
  • PP 405 old – 5322 321 23787 Print Head Cable
  • PP 404/405 new – 8707 901 00030 Print Head Cable
  • PP 407/408 old – 5322 321 62441 Print Head Cable
  • PP 407/408 new- 8707 901 00038 Print Head Cable
[bsf-info-box icon="Defaults-close remove times" icon_size="32" icon_color="#dd3333"][/bsf-info-box]

Possible Cause 2

The Print H encoder or encoder strip or the signal transmission via the 4-pin connector on the printhead cables into the DEV is defective. During the initialization of the carriage moves violently against the right side wall and stops there.

[bsf-info-box icon="Defaults-check" icon_size="32" icon_color="#81d742"][/bsf-info-box]

Solution

Order numbers:

  • PP 40X old – 5322 218 80713 Print H-Encoder
  • PP40X new – 8707 901 00031Print H-Encoder 2
  • PP 40X old/new – 5322 466 11114 Encoder Strip 2
[bsf-info-box icon="Defaults-close remove times" icon_size="32" icon_color="#dd3333"][/bsf-info-box]

Possible Cause 3

The horizontal or motors are defective. Replace in pairs in the PP407 /. 8 The engines have about 4 ohms internal resistance and are connected in series in PP407.

[bsf-info-box icon="Defaults-check" icon_size="32" icon_color="#81d742"][/bsf-info-box]

Solution

Order numbers:

  • PP 404/405 old – 5322 361 21304 H-Motor
  • PP 404/405 new – 8707 901 00032 H-Motor 2
  • PP 407/408 old – 5322 361 10757 H-Motor left
  • PP 407/407new  -8707 901- 00039 H-MOTOR LEFT PP407/8-2
  • PP 407/408 old – 5322 361 10758 H-Motor right
  • PP 407/408 new – 8707 901 00040 H-MOTOR RIGHT PP407/8-2
[bsf-info-box icon="Defaults-close remove times" icon_size="32" icon_color="#dd3333"][/bsf-info-box]

Possible Cause 4

The rubber buffer (left stopper) in the left side wall is missing or destroyed.

[bsf-info-box icon="Defaults-check" icon_size="32" icon_color="#81d742"][/bsf-info-box]

Solution

Order number:
PP 40X – 5322 310 11261 Kit Left Stopper

[bsf-info-box icon="Defaults-close remove times" icon_size="32" icon_color="#dd3333"][/bsf-info-box]

Possible Cause 5

The ribbon gear is broken so that the Druckkopfumschalthebel is on the printhead-switchable-position. This position hinders the horizontal movement of the carriage and prevents it from coming to the end position.

[bsf-info-box icon="Defaults-check" icon_size="32" icon_color="#81d742"][/bsf-info-box]

Solution

Order number:

  • PP 40X old – 5322 522 10431 Ribbon Gear
  • PP 40X new- 8707 901 00014 RIBBON GEAR – R
[bsf-info-box icon="Defaults-close remove times" icon_size="32" icon_color="#dd3333"][/bsf-info-box]

Possible Cause 6

The tractor transmission is defective, so that the paper source selection lever can not turn. A blockade hinders the horizontal movement of the carriage and prevents it from coming to the end position.

[bsf-info-box icon="Defaults-check" icon_size="32" icon_color="#81d742"][/bsf-info-box]

Abhilfe

Ordernummern:
PP 40X – 5322 522 10432 Tractor Gear

My matrix printer prints very slowly from a Windows environment

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

It is recommended to use the PSi original printer driver and use of the application only internal printer fonts. TrueType fonts are fonts graphics printed with graphics speeds.
However, if the need TrueType fonts to use, the PP40x) and all models offer the possibility of accelerating the Grafidruckes. In macro menu setting the print quality is there, the menu item for graphic quality.
The following settings are possible:

  • Standard
  • WIN LQ 180 dpi
  • WIN NLQ 90 dpi
  • WIN DRAFT 60 dpi

Depending on the print quality, the printing speed is to be increased. However, the font size is retained. Likewise, these settings can be made in the printer driver.

Grafikbeschleunigung

How can internal barcodes on a PP 40x / 80x PP print from Windows?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

Use an internal font in your application. Enter Barcode commands and start / stop commands. These are described in the User Guide Barcode Quick Reference Guide. Use $$ instead of ESC [and select the Printers menu $$ – Emulation. The bar code is not shown on the screen.

How to cut jobs with multiple pages and without pauses between each jobs with PP 408?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

In Job should be additional sequences installed:

  • ESC[;;;30 73 für Cut Mode OFF
  • ESC[;;;31 73 für Cut Mode ON (after next Form Feed)
  • ESC[;;;32 73 for cutting at the current position + 4mm

For this please is the printer documentation observed.

At job start “Cut Mode OFF” insert to prevent accidental cutting at FF.

At the desired site “cutting at the current position” insert if not to be cut at bottom of page.

For cutting at bottom of page “Cut Mode ON” and, if necessary. A FF (0C) insert.

How can the performance be increased in barcode printing?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

Printed with the Font Data also bar with PSi sequences, optimizing performance is possible.
The parameter P7 should preferably be set to the value “3” in the barcode sequence on the system side. Then the PSi barcode is printed in “NLQ unidirectional”. This is sufficient for most applications. Tests with readers, however, are recommended.

ESC[;P2;P3;P4;P5;P6;P7_z (Note:_ = Space)

Background:
By default, the printer uses the parameter P7 is “1” (= LQ unidirectional). For this, the print head must also be brought into the appropriate position. If the surrounding text in DATA / DRAFT printed in the other print head position, here switchover pauses are inevitable.

Details see Appendix Barcode Quick Reference Manual of the respective printer

Buffer Overflow by operating serial interfaces

Verlust von Einstellungen im Menü. Der Drucker hat plötzlich wieder Fabrikeinstellungen.

[bsf-info-box icon="Defaults-close remove times" icon_size="32" icon_color="#dd3333"][/bsf-info-box]

Cause of

The pull-up resistor for the Cond CTS (PIN 5 on 25-pol. Connector) is not due to + 12V to + 5V but. Thus, sending X-OFF / X-ON is non-connected at
CTS -Ltg. suspended because the level does not min. 3V reached.

[bsf-info-box icon="Defaults-check" icon_size="32" icon_color="#81d742"][/bsf-info-box]

Solution

Set a Bridge from PIN 20 to PIN 5 in the cable or connector PM.

Which adapter do I need to operate PP40x New with Serial standard V24 cable?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

Seriell-Adapter

Infrequent vertical offset in PP 40x

[bsf-info-box icon="Defaults-close remove times" icon_size="32" icon_color="#dd3333"][/bsf-info-box]

Possible cause 1:
The pressure of the Paper Guide 4 is no longer uniform.

[bsf-info-box icon="Defaults-check" icon_size="32" icon_color="#81d742"][/bsf-info-box]

Solution

Order numbers:
PP 404 – 5322 466 11768
PP 405 – 5322 466 11766
PP 407 / PP 408 – 5322 466 83095

Paper Guide 4 Remove the two green thumbscrews and test paper run, or changePaper Guide 4  of another printer. Check then the paper flow is braked. If with removed Paper Guide 4 the paper but not run properly with the new paper guide 4, then FF2 could not be installed properly. The rubber rollers must not rub against the sheet. Possibly the gear is right not deep enough on the shaft. Gear and shaft end must be flush. Game Wave permitted with gear 0.5mm.

[bsf-info-box icon="Defaults-close remove times" icon_size="32" icon_color="#dd3333"][/bsf-info-box]

Possible Cause 2:
The Belt Pulley’s are broken into the receiving pins.

[bsf-info-box icon="Defaults-check" icon_size="32" icon_color="#81d742"][/bsf-info-box]

Solution

Order numbers:
PP 404/405 – 5322 310 11313
PP 407/408 – 5322 310 32139

When the upper pulley is white, then it is an old pulley, which should be replaced by a black. Examination of Pulleys: screw and washer decrease Pulley must not be rotated by hand on the axis.

[bsf-info-box icon="Defaults-close remove times" icon_size="32" icon_color="#dd3333"][/bsf-info-box]

Possible Cause 3:
The FF-roller  of V-Transports are worn out.

[bsf-info-box icon="Defaults-check" icon_size="32" icon_color="#81d742"][/bsf-info-box]

Solution

Order numbers:
PP 404 – 5322 310 11123 Kit V-Transport
PP 405 – 5322 310 31375 Kit V-Transport
PP 407/408 – 5322 535 93473 Shaft FF 1(only at feeding problems)
PP 407/408 – 5322 535 93474 Shaft FF 2
Diameter nominally 20.26mm, worn <20:15 mm

[bsf-info-box icon="Defaults-close remove times" icon_size="32" icon_color="#dd3333"][/bsf-info-box]

Possible cause 4: With PP405 / 408
Kit Cont. Forms or Kit Dollies is defective.

[bsf-info-box icon="Defaults-check" icon_size="32" icon_color="#81d742"][/bsf-info-box]

Solution

Order numbers:
PP 405 – 5322 310 31376 Kit Cont. Forms
PP 408 – 5322 310 10623 Kit Transport Roller (placed in cutter)

[bsf-info-box icon="Defaults-close remove times" icon_size="32" icon_color="#dd3333"][/bsf-info-box]

Possible cause 5: PP 407/408
Kit Tractor Exit is defective.

[bsf-info-box icon="Defaults-check" icon_size="32" icon_color="#81d742"][/bsf-info-box]

Solution

Order numbers:
PP 408 – 5322 310 10628 (iin the cutter)
PP 407 – 5322 310 10628 (last roller in the printer)

test freewheel: sideways driving gear by hand and fix the shaft by hand. Gear must not by ratcheting in the drive direction.

[bsf-info-box icon="Defaults-close remove times" icon_size="32" icon_color="#dd3333"][/bsf-info-box]

Possible Cause 6:
Paper Sensor (Paperin / run) no longer works reliably.

[bsf-info-box icon="Defaults-check" icon_size="32" icon_color="#81d742"][/bsf-info-box]

Solution

Order numbers:
PP 404/405 – 5322 693 22604
PP 407/408 – 5322 693 23162

Permanent occurring vertical shift at PP40x printers

[bsf-info-box icon="Defaults-close remove times" icon_size="32" icon_color="#dd3333"][/bsf-info-box]

Permanent vertical  offset:

Line prior to the first 1 – added 3 pages: Check Cause 2 or 3 Cause (FF2). Transport in the cutter slows down the paper path. To test Fold down the cutter and leave the paper running over the cutter.
Printhead plate defective or soiled with glue / adhesive label. Remove roller and check the print head shield.
Typical error: When paper feed pushes the upper edge of the paper and moves or verreißt the paper.
Info: Check for repairing the correct locking of paper guide 4 Paper Guide 1, Loosen the crews and tighten.

Line 1 is too high, pressure is at perforation.
Paper sensor possibly replaced during repair and confused with the sensor of PP404 / PP407 405 or / 408th Check Adjust the printer’s menu and adjust as necessary. Paper bump (wave) before the first pair of rollers FF1:
The paper is already under FF2, cause almost always in the rear driving area.Tractor doors dawned tractor doors in tractor cassette has dawned and can slow down the paper depending on the paper thickness.
Solution: Replace Tarktorkassette
Paper is torn from the tractor, it incur slots at PP 407 and PP 408th

Possible Cause 1:
The roles of the Paper Guide 4 swollen (circumferential speed is higher) and pull the paper with more train from the tractors.
Solution: Paper Guide 4 5322 466 83095 exchange.

Possible Cause 2:
The pressure of the Paper Guide is one-sided. The paper is pulled to one side.
Solution: Paper Guide 4 5322 466 83095 exchange

[bsf-info-box icon="Defaults-check" icon_size="32" icon_color="#81d742"][/bsf-info-box]

Abhilfe

Prüfen Ursache 2 oder Ursache 3 (sporadisch auftretender Vertikalversatz).

[bsf-info-box icon="Defaults-close remove times" icon_size="32" icon_color="#dd3333"][/bsf-info-box]

Mögliche Ursache 2

Transport im Cutter bremst den Papierlauf

[bsf-info-box icon="Defaults-check" icon_size="32" icon_color="#81d742"][/bsf-info-box]

Abhilfe

Zur Prüfung den Cutter abklappen und das Papier über den Cutter laufen lassen.

[bsf-info-box icon="Defaults-close remove times" icon_size="32" icon_color="#dd3333"][/bsf-info-box]

Mögliche Ursache 3

Druckkopfschild defekt oder mit Kleber / Klebeetikette verschmutzt.

[bsf-info-box icon="Defaults-check" icon_size="32" icon_color="#81d742"][/bsf-info-box]

Abhilfe

Walze ausbauen und Druckkopfschild prüfen.

[bsf-info-box icon="Defaults-close remove times" icon_size="32" icon_color="#dd3333"][/bsf-info-box]

Mögliche Ursache 4

Typischer Fehler: Beim Papiertransport stößt die obere Papierkante an und verschiebt oder verreißt das Papier.

[bsf-info-box icon="Defaults-check" icon_size="32" icon_color="#81d742"][/bsf-info-box]

Abhilfe

Info: Nach Reparatur den korrekten Sitz von Paperguide 4, Paperguide 1 prüfen, Schrauben lösen und wieder festziehen.

[bsf-info-box icon="Defaults-close remove times" icon_size="32" icon_color="#dd3333"][/bsf-info-box]

Mögliche Ursache 5

1. Zeile ist zu hoch, Druck erfolgt auf Perforation. Papiersensor evtl. bei Reparatur getauscht und mit dem Sensor von PP404/405 oder PP407/408 verwechselt.

[bsf-info-box icon="Defaults-check" icon_size="32" icon_color="#81d742"][/bsf-info-box]

Abhilfe

Adjust im Menü des Druckers überprüfen und ggf. einstellen.

[bsf-info-box icon="Defaults-close remove times" icon_size="32" icon_color="#dd3333"][/bsf-info-box]

Mögliche Ursache 6

Papierbeule (Welle) vor dem ersten Rollenpaar FF1

[bsf-info-box icon="Defaults-check" icon_size="32" icon_color="#81d742"][/bsf-info-box]

Abhilfe

Das Papier ist bereits unter FF2, Ursache fast immer im hinteren Antriebsbereich.
Traktorklappe angebrochen: Traktorklappe in der Traktorkassette ist angebrochen und kann das Papier je nach Papierdicke bremsen.
Lösung: Tarktorkassette tauschen

Paper is torn from the tractor, it caused long holes in PP 407 and PP 408 printers

[bsf-info-box icon="Defaults-close remove times" icon_size="32" icon_color="#dd3333"][/bsf-info-box]

Possible Cause:

The roles of the Paper Guide 4 have swollen (circumferential speed is higher) and pull the paper with more train from the tractors.

[bsf-info-box icon="Defaults-check" icon_size="32" icon_color="#81d742"][/bsf-info-box]

Abhilfe

Paper Guide 4 5322 466 83095 austauschen.

[bsf-info-box icon="Defaults-close remove times" icon_size="32" icon_color="#dd3333"][/bsf-info-box]

Mögliche Ursache 2

Der Andruck des Paper Guide ist einseitig. Das Papier wird zu einer Seite gezogen.

[bsf-info-box icon="Defaults-check" icon_size="32" icon_color="#81d742"][/bsf-info-box]

Abhilfe

Paper Guide 4 5322 466 83095 austauschen.

How to perform a HEX Dump in PP 40x printers?

The HEXdump provides the ability to stream to analyze. It shows all control characters, which are sent to the printer. To this end, the HEX-DUMP is selected in the menu. Then you send the original file to the printer. All data are printed in HEX code line by line.

Hex_dump_80x

Perform a HEX-DUMP PP40x_de_eng

How to adjust the tear off position in PP40x printers?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

The tear bar may in the installation menu in increments of 1 – are laid 360/60 up to 6 inches. Refer to the instruction.

CHANGE TEAR OFF POSITION PP40x_de_eng

How to realign the optical sensors of PR9?

The reason of a permanent misalignment of paper in PR9 may be due to incorrect storage values of the optical sensors. This can be realigned. Go according to the procedure:

Ausrichten der optischen Sensoren PR9

How to increase the speed in draft mode (HSD)

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

The quality of the font data can be selected in 2 steps or 2 speeds.

How can I install a PM-Ethernet on AS 400 / iSeries?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Installation Instructions for Standard PM Ethernet 10/100 MBit without SCS converter to an AS400 / iSeries

The print servers fully support the SCS data stream of the IBM AS / 400 / iSeries. For IPDS data, only the conversion of fonts is possible. Other IPDS features still have to be implemented by specific IPDS data stream converters that are connected between the system and printer. In AS / 400 networks, network printers can be operated in two different ways:

  • a remote output queue (RMTPRTQ)
  • a device description

The procedure they refer to the PDF file.

matrix unter AS400_ENG

How I install a PSi Printer Drivers on Windows Server?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

What factors are important when LPR Printing with PM PNS PP 40x

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

For LPR Printing from Windows the byte count must be activated .

1064-lpr_001

 

 

 

 

 

 

 

 

 

 

 

Reason:

“LPR Byte Counting” forcing Windows to count the number of bytes in the file and sends this value to the data of the received file as a command. If LPR byte count is disabled, Microsoft puts on a size which is much larger than the actual file size. It is neither 0 nor the actual file size.

How to install a 32 bit drivers on a 64 bit system?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

32-bit printer driver issues on a Windows Server When you install an additional x86 printer driver on 64-bit Windows  is to come on the instructions of the driver, the message: “path to Windows media (x64 processor)”. Here, after a “ntprint.inf” file is needed. These can be supplied with a small workaround.

32 Bit driver installation on 64 Bit Server

How Win7 / Win8 a driver package permanently delete?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

This is always necessary if a newer printer driver same names will be installed.

WIN 7 8 delete driver incl package

How to install unsigned drivers under Win8?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

On Windows 8 can not certified printer driver only install if Win 8 allows this. For this purpose, allowing mss be unlocked. Here’s a quick way.

Install an unsigned driver on Windows 8

How to install an unsigned driver under Windows Server 2012?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

On Windows Server 2012 you can not  certified printer driver only install if Win Serv. 2012, this also permits. For this purpose, the Permit must be unlocked. Here’s a quick way:

Install an unsigned driver on Windows 2012

How can I install an unsigned windows 10 driver?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

Under Windows 10 allow non-certified printer driver only install if Win10 also allows this. For this purpose, the Permit must be unlocked. Here’s a quick way:

install unsigned driver under Windows 10

My matrix printer prints very slowly from a Windows environment

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

It is recommended to use the PSi original printer driver and use of the application only internal printer fonts. TrueType fonts are fonts graphics printed with graphics speeds.
However, if the need TrueType fonts to use, the PP40x) and all models offer the possibility of accelerating the Grafidruckes. In macro menu setting the print quality is there, the menu item for graphic quality.
The following settings are possible:

  • Standard
  • WIN LQ 180 dpi
  • WIN NLQ 90 dpi
  • WIN DRAFT 60 dpi

Depending on the print quality, the printing speed is to be increased. However, the font size is retained. Likewise, these settings can be made in the printer driver.

Grafikbeschleunigung

How to install a Printer Stand PP 405 ?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

FSI_19273

How to install a Printer Stand PP 407 ?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

FSI_19273

How to install a Printer Stand PP 408 ?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

FSI_19273

How to install a Printer Stand PP 803 ?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

FSI_19273

How to install a Printer Stand PP 806 / PP 809 ?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

FSI_19273

How to create a Custom Paper Size in Windows?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

To define a custom paper size under Windows , must be taken as follows:

  • Open the Printers folder
  • from the Win 7 version must be marked any printer. Then the item will appear in the upper menu bar “Server Properties”
  • WIN XP / Vista version via the File menu “Server Properties” Select.
  • now there is a custom form can be created and saved under a freely selectable name.
  • The form is then in all printer drivers are available that support this form size.

Important:you need  administrative rights to create new forms.

How to reset an Ethernet print server to factory defaults?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

The print server can be reset using a key combination to the factory delivery status manually.

Procedure to remove the attached documents:

  • Status button to print a status page.
  • The corresponding Ethernet Release can be read from there Status page ..
  • Depending on the release procedure differs

Print Server Reset For PM Ethernet PS_IC 102 Rel_eng

How to set Start / Stop or strings changes in the “Logical Printer” of PM Ethernets?

[bsf-info-box icon="Defaults-info-circle" icon_size="32" icon_color="#1e73be"][/bsf-info-box]

Information

Strings can be passed by decimal code. A backslash directs the Decimal character (unconditional 3-digit decimal notation). Characters that do not control characters are able to pass directly into ASCII.

 

StringChange_PM_Ethernet